Image de couverture de l'utilisateur
Photo de profil

john35588

DIYFPV Explorer badge
Vu pour la dernière fois : 22 nov., 05:12
Abonnés
6
Abonnements
12
Votes positifs
0
Publications
1
Pretty new to the FPV world, but loving it so far! My custom Source One V6 parts: https://www.thingiverse.com/thing:7280553

Fil d'activité

21 novembre 2026 à 17:47

A commenté le post de
Welcome to Utah! Depending on where you’re at I’m sure there are many places for long range, but I don’t have much experience with long range flying. The Salt Flats are huge and flat, or there are mountains all around.
Where in Utah are you visiting?

17 novembre 2026 à 19:33

A commenté le post de
Is your camera angle already as low as it can go? FPV drones typically have the camera angle at around 20-35° because, when you're flying forward, it angles the drone down so the camera can see what's ahead.
If you're recording stationary or slow-moving subjects, you might be better off with a DJI Neo or similar drone. Otherwise, I'd try increasing your speed and using Acro mode instead of Angle mode (if that's what you're using).

17 novembre 2026 à 19:20

A commenté le post de
I have an Ender 3 (which is likely the model he's offering if it is an Ender), and I love it. That said, it isn't necessarily a plug-and-play printer like Bambu Labs printers are. You'll have to do some tinkering and playing with settings to get it to print just right. 3D printing is a learning curve, and you'll be surprised at how many random issues you'll have to become familiar with. 
The Ender 3 typically goes for just under $200 USD, and filament is usually $20 per kilogram. The printer and some filament for just $100 sounds like a good deal to me, and if you play with it for a few weeks and decide it isn't for you, you can probably get your money back by reselling it on Facebook Marketplace or elsewhere.

16 novembre 2026 à 21:41

A commenté le post de
I don't think they ship until March of 2027, so I doubt anyone has them yet. They look pretty cool, and I love the idea of open-source hardware, though!

16 novembre 2026 à 21:39

A commenté le post de
They exist, but depending on what your use case is, you might have to design something yourself.
Flying an FPV drone with a negative camera angle is difficult, so you might be better off with a pre-built drone with a camera gimbal, a 360° camera, or a custom drone with two cameras, one for recording and one for flying.

What are you wanting to use the drone for?

16 novembre 2026 à 16:50

A commenté le post de
It's getting pretty cold here pretty quickly, and we're expecting snow by the end of the week. I don't expect to be able to pull out the 5" for at least 3-4 months.
Great flying!

18 octobre 2026 à 06:16

A commenté le post de
The BetaFPV Meteor65/75 Pro has been pretty popular recently. I’ve been loving mine.

14 octobre 2026 à 02:36

A commenté le post de
I would imagine an organized event would have channel assignments planned out ahead of time. They can also use tools like this one to find the best channels for a variety of pilots: https://www.diyfpv.com/resources/fpv-channel-organiser

7 octobre 2026 à 05:12

A commenté le post de
Yep, I'd recommend cleaning up both the positive and negative pads and resoldering. Make sure you're holding the soldering iron against the pad and wire long enough that the solder can make a solid connection. It will not last if the pad isn't hot enough. 

If your soldering iron gets any hotter, I would turn it up. Some of your solder joints look like they could use some additional heat. This site has some good advice for soldering: https://learn.adafruit.com/adafruit-guide-excellent-soldering/common-problems#step-418535

7 octobre 2026 à 03:54

A commenté le post de
Can you upload a picture? I’m guessing you’re not letting the pad get hot enough while soldering.

5 octobre 2026 à 18:42

A commenté le post de
If the motors are feeling wobbly then it’s almost certainly the bearings having gone out. The bearings are supposed to hold the bell perfectly parallel to the stator so they don’t rub. 
You can fly it like this, but the vibrations will likely get worse, and your motors will probably get hotter than they would before.


The best move would be to replace them.

5 octobre 2026 à 15:52

A commenté le post de
Did you disassemble the motors, completely removing the bell from the stator, when cleaning? If so, it is possible that your motor bearings are failing, and you might just have to get new motors to solve this problem.

25 septembre 2026 à 03:19

23 septembre 2026 à 05:37

A commenté le post de
Great idea! I'll have to keep this in mind, my Meteor75 is on its way!

23 septembre 2026 à 05:35

A commenté le post de
It's difficult to give a good estimate. Many parts have sat at that point for a while because we've been making sure the builder is completely ready before releasing it (the community was much faster at building parts than we expected!).
Over the next week or two, we should be able to publish many more parts now that the builder has been released.

23 septembre 2026 à 05:31

A commenté le post de
It really depends on what you're looking for and what you're willing to spend.
If your budget is low and you're just excited about flying, go analog.
If you have a high budget and are interested in high-quality video, pick a digital option.


This article is a pretty long-winded answer, but it has a ton of useful information for making this choice: https://oscarliang.com/fpv-system/

22 septembre 2026 à 19:53

A commenté le post de
Congratulations, and great work, it looks awesome!

22 septembre 2026 à 19:25

A présenté un build : John's 5" Freestyle Build

4 septembre 2026 à 06:07

A commenté le post de
I've done the same oscilloscope and function generator kits! They're great for learning how to solder, and I've found the oscilloscope to be pretty handy in some other projects, despite its inaccuracies.
I found these instructions on how to make the oscilloscope work with USB power, and there's a mod included at the end that can make the reading much cleaner, but I haven't had the time to try either mod yet: https://www.instructables.com/DSO138-USB-Power-No-Boost-Converter/

Prenons notre envol ensemble et propulsons le monde des drones FPV vers de nouveaux sommets.

© 2026 DIYFPV. Tous droits réservés.