Benutzer-Titelbild
Benutzerbild

john35588

DIYFPV Explorer badge
Zuletzt gesehen: 22. Nov., 05:12
Follower
6
Folge ich
12
Positive Bewertungen
0
Beiträge
1
Pretty new to the FPV world, but loving it so far! My custom Source One V6 parts: https://www.thingiverse.com/thing:7280553

Aktivitätsfeed

21. November 2026 um 17:47

Hat den Beitrag von kommentiert
Welcome to Utah! Depending on where you’re at I’m sure there are many places for long range, but I don’t have much experience with long range flying. The Salt Flats are huge and flat, or there are mountains all around.
Where in Utah are you visiting?

17. November 2026 um 19:33

Hat den Beitrag von kommentiert
Is your camera angle already as low as it can go? FPV drones typically have the camera angle at around 20-35° because, when you're flying forward, it angles the drone down so the camera can see what's ahead.
If you're recording stationary or slow-moving subjects, you might be better off with a DJI Neo or similar drone. Otherwise, I'd try increasing your speed and using Acro mode instead of Angle mode (if that's what you're using).

17. November 2026 um 19:20

Hat den Beitrag von kommentiert
I have an Ender 3 (which is likely the model he's offering if it is an Ender), and I love it. That said, it isn't necessarily a plug-and-play printer like Bambu Labs printers are. You'll have to do some tinkering and playing with settings to get it to print just right. 3D printing is a learning curve, and you'll be surprised at how many random issues you'll have to become familiar with. 
The Ender 3 typically goes for just under $200 USD, and filament is usually $20 per kilogram. The printer and some filament for just $100 sounds like a good deal to me, and if you play with it for a few weeks and decide it isn't for you, you can probably get your money back by reselling it on Facebook Marketplace or elsewhere.

16. November 2026 um 21:41

Hat den Beitrag von kommentiert
I don't think they ship until March of 2027, so I doubt anyone has them yet. They look pretty cool, and I love the idea of open-source hardware, though!

16. November 2026 um 21:39

Hat den Beitrag von kommentiert
They exist, but depending on what your use case is, you might have to design something yourself.
Flying an FPV drone with a negative camera angle is difficult, so you might be better off with a pre-built drone with a camera gimbal, a 360° camera, or a custom drone with two cameras, one for recording and one for flying.

What are you wanting to use the drone for?

16. November 2026 um 16:50

Hat den Beitrag von kommentiert
It's getting pretty cold here pretty quickly, and we're expecting snow by the end of the week. I don't expect to be able to pull out the 5" for at least 3-4 months.
Great flying!

18. Oktober 2026 um 06:16

Hat den Beitrag von kommentiert
The BetaFPV Meteor65/75 Pro has been pretty popular recently. I’ve been loving mine.

14. Oktober 2026 um 02:36

Hat den Beitrag von kommentiert
I would imagine an organized event would have channel assignments planned out ahead of time. They can also use tools like this one to find the best channels for a variety of pilots: https://www.diyfpv.com/resources/fpv-channel-organiser

7. Oktober 2026 um 05:12

Hat den Beitrag von kommentiert
Yep, I'd recommend cleaning up both the positive and negative pads and resoldering. Make sure you're holding the soldering iron against the pad and wire long enough that the solder can make a solid connection. It will not last if the pad isn't hot enough. 

If your soldering iron gets any hotter, I would turn it up. Some of your solder joints look like they could use some additional heat. This site has some good advice for soldering: https://learn.adafruit.com/adafruit-guide-excellent-soldering/common-problems#step-418535

7. Oktober 2026 um 03:54

Hat den Beitrag von kommentiert
Can you upload a picture? I’m guessing you’re not letting the pad get hot enough while soldering.

5. Oktober 2026 um 18:42

Hat den Beitrag von kommentiert
If the motors are feeling wobbly then it’s almost certainly the bearings having gone out. The bearings are supposed to hold the bell perfectly parallel to the stator so they don’t rub. 
You can fly it like this, but the vibrations will likely get worse, and your motors will probably get hotter than they would before.


The best move would be to replace them.

5. Oktober 2026 um 15:52

Hat den Beitrag von kommentiert
Did you disassemble the motors, completely removing the bell from the stator, when cleaning? If so, it is possible that your motor bearings are failing, and you might just have to get new motors to solve this problem.

25. September 2026 um 03:19

23. September 2026 um 05:37

Hat den Beitrag von kommentiert
Great idea! I'll have to keep this in mind, my Meteor75 is on its way!

23. September 2026 um 05:35

Hat den Beitrag von kommentiert
It's difficult to give a good estimate. Many parts have sat at that point for a while because we've been making sure the builder is completely ready before releasing it (the community was much faster at building parts than we expected!).
Over the next week or two, we should be able to publish many more parts now that the builder has been released.

23. September 2026 um 05:31

Hat den Beitrag von kommentiert
It really depends on what you're looking for and what you're willing to spend.
If your budget is low and you're just excited about flying, go analog.
If you have a high budget and are interested in high-quality video, pick a digital option.


This article is a pretty long-winded answer, but it has a ton of useful information for making this choice: https://oscarliang.com/fpv-system/

22. September 2026 um 19:53

Hat den Beitrag von kommentiert
Congratulations, and great work, it looks awesome!

22. September 2026 um 19:25

Hat einen Build vorgestellt: John's 5" Freestyle Build

4. September 2026 um 06:07

Hat den Beitrag von kommentiert
I've done the same oscilloscope and function generator kits! They're great for learning how to solder, and I've found the oscilloscope to be pretty handy in some other projects, despite its inaccuracies.
I found these instructions on how to make the oscilloscope work with USB power, and there's a mod included at the end that can make the reading much cleaner, but I haven't had the time to try either mod yet: https://www.instructables.com/DSO138-USB-Power-No-Boost-Converter/

Lass uns gemeinsam abheben und die Welt der FPV-Drohnen auf ein neues Niveau bringen.

© 2026 DIYFPV. Alle Rechte vorbehalten.