ksal
Ostatnio widziano: 29 wrz, 12:22
Obserwujący
4Obserwowani
4Głosy za
0Wpisy
7Jeszcze nie ma biografii...
Kanał aktywności
27 września 2026 13:15
Opublikowano post
Built a 2in 2s based on the Petrel 85 frame and the BetaFPV O4 HD canopy II. To secure the canopy I just slid the bobbins over four M1.4X8 screws. Install the screws so they are long enough to rest in the round middle part of the bobbins. surprisingly secure.
HGLRC Petrel85
BetaFPV O4 HD canopy II
DJI O4 lite w/Flywoo wide angle lens
JHEMCU G474 ELRS AIO Flight Controller
Happymodel 1103 11000kv motors
2in HQ D2X1.9X4GR 1.5mm props
Lava 580mah 2s battery
Here is a flight vid.
18 września 2026 22:57
Opublikowano post
Just another evening rip in the back yard.
15 września 2026 02:10
Skomentowano post użytkownika
I think this is what you need.
7 września 2026 15:35
Skomentowano post użytkownika
I see. looks like you you are setting up betaflight on a new build.
Could you explain your setup?
7 września 2026 14:58
Skomentowano post użytkownika
Probably because Failsafe is selected in the Modes tab. If you don't need Failsafe on a switch just remove it from the Modes tab.
28 sierpnia 2026 08:11
Skomentowano post użytkownika
Search for SMD inductor kit on Amazon
28 sierpnia 2026 07:59
Skomentowano post użytkownika
This one might work for that camera.
Interesting frame. But its heavier than your current frame. And probably wouldn't freestyle that great cause of that.
If your looking for a new frame, any of the popular 1s 75mm frames should work well with your setup.
Pusher setups do provide a bit more thrust.
https://www.youtube.com/watch?v=6eLqJFtP640
You can freestyle anything in my opinion ☺️
If your looking for a new frame, any of the popular 1s 75mm frames should work well with your setup.
Pusher setups do provide a bit more thrust.
https://www.youtube.com/watch?v=6eLqJFtP640
You can freestyle anything in my opinion ☺️
15 lipca 2026 07:06
Skomentowano post użytkownika
Yes. So unfortunate. The things we find ourselves doing for these quads.
13 lipca 2026 18:55
Skomentowano post użytkownika
Looks good really.
You might be able to smooth those jitters out by raising or lowering TPA Rate.
I would try raising first.
You might be able to smooth those jitters out by raising or lowering TPA Rate.
I would try raising first.
13 lipca 2026 18:33
Skomentowano post użytkownika
Awesome video!
Shouldn't have to guess where it is.
Should be within ~50ft of the last known coordinates before the splash.
I'd revisit :)
Shouldn't have to guess where it is.
Should be within ~50ft of the last known coordinates before the splash.
I'd revisit :)
Perfect!
That's where I pulled those settings, from Air75 freestyle CLI :)
Also keep in mind that flight controller can come with various gyros.
Make sure to use the the CLI settings for the gyro that is installed on your board.
In your case it's the BMI270.
Glad you got it working.
Have fun.
That's where I pulled those settings, from Air75 freestyle CLI :)
Also keep in mind that flight controller can come with various gyros.
Make sure to use the the CLI settings for the gyro that is installed on your board.
In your case it's the BMI270.
Glad you got it working.
Have fun.
Backup your settings first
Type
dump
in the CLI
Then press "Save to file button" to save on your computer
Now copy the following to the CLI
set gyro_lpf1_static_hz = 0
set gyro_lpf2_static_hz = 550
set dyn_notch_count = 2
set dyn_notch_q = 450
set dyn_notch_max_hz = 500
set gyro_lpf1_dyn_min_hz = 0
set gyro_lpf1_dyn_max_hz = 550
set acc_calibration = 17,43,30,1
set dshot_bidir = ON
set dshot_bitbang = AUTO
set motor_pwm_protocol = DSHOT300
set motor_poles = 12
set align_board_yaw = -135
set vbat_scale = 113
set ibata_offset = -600
set yaw_motors_reversed = ON
set small_angle = 180
set simplified_gyro_filter_multiplier = 110
set tpa_rate = 60
set tpa_breakpoint = 1220
save
This should set your filters and board alignment for your gyro
If this doesn't help we'll try PIDs next
Type
dump
in the CLI
Then press "Save to file button" to save on your computer
Now copy the following to the CLI
set gyro_lpf1_static_hz = 0
set gyro_lpf2_static_hz = 550
set dyn_notch_count = 2
set dyn_notch_q = 450
set dyn_notch_max_hz = 500
set gyro_lpf1_dyn_min_hz = 0
set gyro_lpf1_dyn_max_hz = 550
set acc_calibration = 17,43,30,1
set dshot_bidir = ON
set dshot_bitbang = AUTO
set motor_pwm_protocol = DSHOT300
set motor_poles = 12
set align_board_yaw = -135
set vbat_scale = 113
set ibata_offset = -600
set yaw_motors_reversed = ON
set small_angle = 180
set simplified_gyro_filter_multiplier = 110
set tpa_rate = 60
set tpa_breakpoint = 1220
save
This should set your filters and board alignment for your gyro
If this doesn't help we'll try PIDs next
I don't understand why your vtx power is reporting 20 in the OSD. Looking at your vtx table It should be reporting 25. R : 1 : 25
This is just a guess but I think the transmitter is transmitting at 200mw on Channel Race 1 and your not seeing that last zero on the OSD for some reason.
The reason your getting static at 25 meters could be because your goggles are manually set to another channel other than Race 1?
(I can go a few hundred meters on 25mw and still have good video)
Check your goggle settings to see if they are manually set to a different channel.
You can also try using auto scan to make sure it locks on to the channel your vtx is transmitting on.
This is just a guess but I think the transmitter is transmitting at 200mw on Channel Race 1 and your not seeing that last zero on the OSD for some reason.
The reason your getting static at 25 meters could be because your goggles are manually set to another channel other than Race 1?
(I can go a few hundred meters on 25mw and still have good video)
Check your goggle settings to see if they are manually set to a different channel.
You can also try using auto scan to make sure it locks on to the channel your vtx is transmitting on.