YorkieCanadian

Laatst gezien: 15 aug, 03:32

Volgers

Volgend

Upvotes

Berichten

Fpv nerd in the Charlotte metro, looking for chill fellow pilots, meet ups, and explorers. ~Phil3273~

Activiteitenfeed

30 juni 2026 om 16:55

Heeft gereageerd op het bericht van

MRen2011

@MRen2011 right, and with the hdmi in, you'd be in a great spot to test it out. I'm keeping an eye on the openipc systems development.

30 juni 2026 om 12:44

Heeft gereageerd op het bericht van

MRen2011

Partially, but I'm not married to them. They are just the best, and I knew the ban on new dji products was incoming, so I got the goggles and stocked up. I have been wanting to try out Walksnail Avatar though, but I know it's going to be a tier below what I already have. It's still A tier, but not S like O4.

I would look at it this way, DJI is great, but going with the box pro goggles from HDZero, you get 1) HDZeros system, 2) Analoge, 3) high quality input for additional vrx systems you want to try. With DJI, you just get in the DJI ecosystem. Sure n3s are not as much, but you get more bang for your buck in terms of versatility with HDZero.

29 juni 2026 om 16:02

Heeft gereageerd op het bericht van

MRen2011

Tough question. I'd say go with Hdzero if you can find them and look into a walksnail vrx. I say this a someone who will probably keep flying DJI and getting their gear, even after the "EOL". Bardwell mentioned this in his stream yesterday, the HDZeros offer such good input, that the lag from using hdmi in is a non-issue. At some point, I will get a walksnail avatar goggle, and dabble in that ecosystem too.

29 juni 2026 om 15:20

Heeft gereageerd op het bericht van

YorkieCanadian

Yeah, same one. I'm not going to sweat it too much.

29 juni 2026 om 12:53

Heeft een bericht geplaatst

Newest build. I may have goofed up on the perfectness of the solder job on the esc and motor pads, but I am satisfied with the end product 😁!

Frame: TJRC-FJ5. See my previous post about my main concerns. But other than that, it is pretty sturdy and if it breaks, it breaks. I'll just have to replace the arms with the extra in the box. 😭

Motors: Axisflying 2207 1860kv

FC+ESC stack: Sologood F722 60a esc

Video: DJI O4 pro air unit with Foxeer 4+ 10cm Lollipop antennas

Receiver: Radiomaster RP3 diversity 2.4Ghz

GPS: Microair M10g gps with SCD and SCL.

Betaflight Release: I flashed 2025.12.5. I added position hold and altitude hold on the flash options.

Presets: UAVtech 5' (no go pro). Elrs150hz

27 juni 2026 om 00:51

Heeft gereageerd op het bericht van

coolk1dfrfr

Let's start with where are you located(country)? This matters a lot as rules can vary greatly.

24 juni 2026 om 12:34

Heeft gereageerd op het bericht van

YorkieCanadian

Thanks. I'm a little sad that it plastic. I'm probably not going to build it out the way I wanted to. I haven't dealt with plastic drones in over a decade, outside of dji ones.

24 juni 2026 om 02:51

Heeft een bericht geplaatst

Hey y'all!

Does anyone have recent experience with a 5 inch fpv frame with plastic arms? Like any recent builds?

I'm curious if I made a good decision lol. I bought this frame from Ali, yes impulse buy, just to check it out. Just arrived and to my disappointment, the arms are injection molded plastic I think. To the credit of tjrc, they gave extra arms in the box. I'm going to build it out, but I'm cautious of vibrations and yes crashing. But this won't be a beater quad now that I see it has non carbon arms.

5 juni 2026 om 23:04

Heeft gereageerd op het bericht van

BlaqkstarFPV

@BlaqkstarFPV Yeah, especially when it comes to their internal resistance. It's a hard metric to track on the smaller packs. I usually go by their voltage sag when in flight. If I see it doesn't perform like it used to, they go straight to the barbecue.

5 juni 2026 om 21:55

Heeft gereageerd op het bericht van

BlaqkstarFPV

Thank you for sharing this. It's really important to keep an eye on these little energetic packs! I follow the methodology that no matter what I do, no storage system is fully fireproof. I keep a fire extinguisher near by and know all of my ammo can storage boxes lined with welders blankets, and lipo bags and other mitigation practices are only there to keep an incident contained, not stopped. It is important to have a safety plan in place. I'm glad Kraken is safe. You can replace things, you can't replace a life.

28 mei 2026 om 12:41

Heeft gereageerd op het bericht van

MrQuack

Yep, it's a little intimidating at first, but I managed to get my pa01 reset and the instructions are pretty good.

27 mei 2026 om 01:24

Heeft gereageerd op het bericht van

Fancy_PantsFPV

Do it! But you need to consider the motor KV when it comes to 6s and the propeller size. I'm not mechanical/electrical engineer, but I think 2306 are more efficient. This also depends on the prop size and kv. For a 5 inch, 2306 is a big motor and one at a low enough kv would give you a more cruise type craft with lots of torque. Higher would give you more thrust. I like running 2306 1700kv on my 5 inch drones, and 2306 1500kv on my 6 inch ones.

https://oscarliang.com/motors/

https://oscarliang.com/table-prop-motor-lipo-weight/

26 mei 2026 om 13:43

Heeft gereageerd op het bericht van

YorkieCanadian

Here's a video of him taking my Volador VX3.5 out. We had trouble binding his transmitter to it so he had to use mine. I'd say for not being comfortable with someone else's set up, he was pretty comfortable lol

https://youtu.be/vPC-74f1WrY

25 mei 2026 om 21:24

Heeft een bericht geplaatst

Just had a fun flying session with another pilot in my area today lots of fun talking shop and sharing tips and exploring. This post is a shout out to Stu and the devs for creating such an awesome platform for us to connect. I hope I spelled his name correctly haha. Here's what I took out today, (photos are not from today).

Cheers and happy flying y'all!

17 mei 2026 om 16:04

Heeft een bericht geplaatst

PSA: you all probably know, but if you're in the US, pyrodrone.com has o4 pros in stock!

Edit: hope this doesn't go against forum rules. Just wanting to share some good news for us pilots in the US

13 mei 2026 om 20:14

Heeft gereageerd op het bericht van

YorkieCanadian

😍

13 mei 2026 om 13:43

Heeft gereageerd op het bericht van

YorkieCanadian

@tz3den it's actually the sub250 huma

13 mei 2026 om 10:49

Heeft gereageerd op het bericht van

YorkieCanadian

It's probably the flyfish atlas 4. I've swapped out the props for tri-blades and the rear tpu for the stock one.

12 mei 2026 om 19:55

Heeft een bericht geplaatst

Ignore the mess, and don't look to hard at the positive connection lol. I'm proud of being able to knock so much of my replacement volador so quickly today. Hopefully it will have a better life than it's older sibling. Only thing left to do is salvage a o4 pro from another frame and set up

Update: she flies!

11 mei 2026 om 14:18

Heeft gereageerd op het bericht van

YorkieCanadian

What are you talking about, the turtles are having a field day with it now! Lol 🐢🐢🐢 gif