YorkieCanadian

Última visita: 15 ago, 3:32

Seguidores

Siguiendo

Votos positivos

Publicaciones

Fpv nerd in the Charlotte metro, looking for chill fellow pilots, meet ups, and explorers. ~Phil3273~

Feed de actividad

30 de junio de 2026 a las 16:55

Ha comentado la publicación de

MRen2011

@MRen2011 right, and with the hdmi in, you'd be in a great spot to test it out. I'm keeping an eye on the openipc systems development.

30 de junio de 2026 a las 12:44

Ha comentado la publicación de

MRen2011

Partially, but I'm not married to them. They are just the best, and I knew the ban on new dji products was incoming, so I got the goggles and stocked up. I have been wanting to try out Walksnail Avatar though, but I know it's going to be a tier below what I already have. It's still A tier, but not S like O4.

I would look at it this way, DJI is great, but going with the box pro goggles from HDZero, you get 1) HDZeros system, 2) Analoge, 3) high quality input for additional vrx systems you want to try. With DJI, you just get in the DJI ecosystem. Sure n3s are not as much, but you get more bang for your buck in terms of versatility with HDZero.

29 de junio de 2026 a las 16:02

Ha comentado la publicación de

MRen2011

Tough question. I'd say go with Hdzero if you can find them and look into a walksnail vrx. I say this a someone who will probably keep flying DJI and getting their gear, even after the "EOL". Bardwell mentioned this in his stream yesterday, the HDZeros offer such good input, that the lag from using hdmi in is a non-issue. At some point, I will get a walksnail avatar goggle, and dabble in that ecosystem too.

29 de junio de 2026 a las 15:20

Ha comentado la publicación de

YorkieCanadian

Yeah, same one. I'm not going to sweat it too much.

29 de junio de 2026 a las 12:53

Ha creado una publicación

Newest build. I may have goofed up on the perfectness of the solder job on the esc and motor pads, but I am satisfied with the end product 😁!

Frame: TJRC-FJ5. See my previous post about my main concerns. But other than that, it is pretty sturdy and if it breaks, it breaks. I'll just have to replace the arms with the extra in the box. 😭

Motors: Axisflying 2207 1860kv

FC+ESC stack: Sologood F722 60a esc

Video: DJI O4 pro air unit with Foxeer 4+ 10cm Lollipop antennas

Receiver: Radiomaster RP3 diversity 2.4Ghz

GPS: Microair M10g gps with SCD and SCL.

Betaflight Release: I flashed 2025.12.5. I added position hold and altitude hold on the flash options.

Presets: UAVtech 5' (no go pro). Elrs150hz

27 de junio de 2026 a las 0:51

Ha comentado la publicación de

coolk1dfrfr

Let's start with where are you located(country)? This matters a lot as rules can vary greatly.

24 de junio de 2026 a las 12:34

Ha comentado la publicación de

YorkieCanadian

Thanks. I'm a little sad that it plastic. I'm probably not going to build it out the way I wanted to. I haven't dealt with plastic drones in over a decade, outside of dji ones.

24 de junio de 2026 a las 2:51

Ha creado una publicación

Hey y'all!

Does anyone have recent experience with a 5 inch fpv frame with plastic arms? Like any recent builds?

I'm curious if I made a good decision lol. I bought this frame from Ali, yes impulse buy, just to check it out. Just arrived and to my disappointment, the arms are injection molded plastic I think. To the credit of tjrc, they gave extra arms in the box. I'm going to build it out, but I'm cautious of vibrations and yes crashing. But this won't be a beater quad now that I see it has non carbon arms.

5 de junio de 2026 a las 23:04

Ha comentado la publicación de

BlaqkstarFPV

@BlaqkstarFPV Yeah, especially when it comes to their internal resistance. It's a hard metric to track on the smaller packs. I usually go by their voltage sag when in flight. If I see it doesn't perform like it used to, they go straight to the barbecue.

5 de junio de 2026 a las 21:55

Ha comentado la publicación de

BlaqkstarFPV

Thank you for sharing this. It's really important to keep an eye on these little energetic packs! I follow the methodology that no matter what I do, no storage system is fully fireproof. I keep a fire extinguisher near by and know all of my ammo can storage boxes lined with welders blankets, and lipo bags and other mitigation practices are only there to keep an incident contained, not stopped. It is important to have a safety plan in place. I'm glad Kraken is safe. You can replace things, you can't replace a life.

28 de mayo de 2026 a las 12:41

Ha comentado la publicación de

MrQuack

Yep, it's a little intimidating at first, but I managed to get my pa01 reset and the instructions are pretty good.

27 de mayo de 2026 a las 1:24

Ha comentado la publicación de

Fancy_PantsFPV

Do it! But you need to consider the motor KV when it comes to 6s and the propeller size. I'm not mechanical/electrical engineer, but I think 2306 are more efficient. This also depends on the prop size and kv. For a 5 inch, 2306 is a big motor and one at a low enough kv would give you a more cruise type craft with lots of torque. Higher would give you more thrust. I like running 2306 1700kv on my 5 inch drones, and 2306 1500kv on my 6 inch ones.

https://oscarliang.com/motors/

https://oscarliang.com/table-prop-motor-lipo-weight/

26 de mayo de 2026 a las 13:43

Ha comentado la publicación de

YorkieCanadian

Here's a video of him taking my Volador VX3.5 out. We had trouble binding his transmitter to it so he had to use mine. I'd say for not being comfortable with someone else's set up, he was pretty comfortable lol

https://youtu.be/vPC-74f1WrY

25 de mayo de 2026 a las 21:24

Ha creado una publicación

Just had a fun flying session with another pilot in my area today lots of fun talking shop and sharing tips and exploring. This post is a shout out to Stu and the devs for creating such an awesome platform for us to connect. I hope I spelled his name correctly haha. Here's what I took out today, (photos are not from today).

Cheers and happy flying y'all!

17 de mayo de 2026 a las 16:04

Ha creado una publicación

PSA: you all probably know, but if you're in the US, pyrodrone.com has o4 pros in stock!

Edit: hope this doesn't go against forum rules. Just wanting to share some good news for us pilots in the US

13 de mayo de 2026 a las 20:14

Ha comentado la publicación de

YorkieCanadian

😍

13 de mayo de 2026 a las 13:43

Ha comentado la publicación de

YorkieCanadian

@tz3den it's actually the sub250 huma

13 de mayo de 2026 a las 10:49

Ha comentado la publicación de

YorkieCanadian

It's probably the flyfish atlas 4. I've swapped out the props for tri-blades and the rear tpu for the stock one.

12 de mayo de 2026 a las 19:55

Ha creado una publicación

Ignore the mess, and don't look to hard at the positive connection lol. I'm proud of being able to knock so much of my replacement volador so quickly today. Hopefully it will have a better life than it's older sibling. Only thing left to do is salvage a o4 pro from another frame and set up

Update: she flies!

11 de mayo de 2026 a las 14:18

Ha comentado la publicación de

YorkieCanadian

What are you talking about, the turtles are having a field day with it now! Lol 🐢🐢🐢 gif