Darkbrewery

Laatst gezien: 18 okt, 20:37

Volgers

Volgend

Upvotes

Berichten

Nog geen bio...

Activiteitenfeed

24 september 2026 om 00:10

Heeft een bericht geplaatst

Very cool

https://www.youtube.com/watch?v=i1IQXR6Rr4o

11 september 2026 om 17:22

Heeft gereageerd op het bericht van

BrickFPV

So close! Loads of parts are ready to publish, we are just finishing testing on the newest version of the builder.

11 september 2026 om 15:57

Heeft gereageerd op het bericht van

TheoHerd30

You sir, are in luck- and looks like @Docfail has done the work!

9 september 2026 om 17:08

Heeft gereageerd op het bericht van

w4s1m

We should be all caught up now! I've spent about a week now getting to everything submitted. Please check that all "blocking" comments are resolved on your parts, its the only way we can see that they are ready for another look. Currently have about 60 parts ready to publish, but almost 200 parts users have not resolved changes requested on.

9 september 2026 om 16:13

Heeft gereageerd op het bericht van

w4s1m

I believe we are at over 300 parts, but the truth is that the builder has been going through many iterations of development on the backend and is in its final phase of testing now.

5 september 2026 om 02:38

Heeft gereageerd op het bericht van

braxtonfpv

nada?

24 augustus 2026 om 16:00

Heeft gereageerd op het bericht van

M4R5_FPV

What are the 4 jumpers for?

23 juli 2026 om 02:24

Heeft gereageerd op het bericht van

bzaebst83

What is it? Context? Spam?

21 juli 2026 om 17:03

Heeft gereageerd op het bericht van

LouisXVIII

Hey Louis, I've tagged the team with your issues.

For the images they are checking into why permissions aren't set for users to upload custom images. For the grid issue, have you tried zooming in closer for a tighter snap grid? Also I find that using the arrow keys helps nudge parts in finer increments than dragging with the mouse does.

Then for the component stacking yeah, that's annoying. For now its whatever is added last gets the higher z index value. Labels and silkscreens have to be added as a final step or they do get covered up.

For your two sided part, does it let you assign the same image for both front and back?

20 juli 2026 om 22:13

Heeft gereageerd op het bericht van

M4R5_FPV

Blame Bardwell's video? We are seeing tons of great parts being submitted in the builder.

For anyone reading and building... We can currently only publish one version of each part. So this means the most detailed and accurate version will usually get picked if it makes it through the review process first. Please know we value everyone's work but are constrained by system requirements.

If you are starting a new part, try to check if multiple people are also working on the same part, and consider building a part not yet in progress.

13 juli 2026 om 22:11

Heeft een bericht geplaatst

Anyone have a Lipo just blowout like this mid flight? Lost power then video. Luckily at low elevation. Took about 45min to find the quad, got away with just one bent prop.

My only setting i had changed was switching the VTX from 200mW to 350mW as my video range was acting funny and not reaching as far as expected.

Not my favorite Lipos anyway... Good excuse to grab som R-Line V6 1000mah's.

3 juli 2026 om 17:18

Heeft gereageerd op het bericht van

M4R5_FPV

I have one of these!

-Make sure your firmware matches in the goggles and the VTX.
-Set your aspect ratio to 4:3 instead of 16:9, this gives gyroflow more to work with when stabilizing
-Use a tiny square shim of shrink tube beneath the cover plate to hold the antennas onto the board more securely
-Replace the antennas with any other LHCP antenna, stock are not great, I use the Ospreys.
- Consider setting up a custom background on your goggles, you can use fine particles to help focus the diopters faster.

29 juni 2026 om 06:51

Heeft gereageerd op het bericht van

Darkbrewery

@tpetersons If you can implement a fix so we can paste from clipboard it would be much better than uploading. Having to save screenshots then dig them out to upload is 4 extra steps.

29 juni 2026 om 06:50

Heeft gereageerd op het bericht van

Darkbrewery

Oh thanks, that makes me feel better knowing it wasn't something on my end completely glossing over something obvious. I'll just chill then.

29 juni 2026 om 06:28

Heeft gereageerd op het bericht van

Darkbrewery

*Edit: I attached screenshots to this post but they were filtered out on posting.

29 juni 2026 om 06:26

Heeft een bericht geplaatst

Can someone please point to the precise RX / TX functions for GPS module pads in the builder? I've resubmitted the same part multiple times but it keeps getting rejected.

> Sees RX on schematic

> Types RX in the search

> Selects "UART - TX" from the list

> Submission gets bounced for not using UART

I'm completely lost, anyone else with this issue?

The GPS tag is not changeable since this is a gps module its added automatically.