S

SiO2

Vu pour la dernière fois : 23 oct., 13:33
Abonnés
2
Abonnements
0
Votes positifs
0
Publications
1
Pas encore de biographie...

Fil d'activité

23 octobre 2026 à 12:47

A commenté le post de
Nothing for Windows but I just tried- FeelFPV tinywhoop on Android ran quite well the controller setup was clunky but ran well once configured. I did try it on Google play for Windows but can't configure my tx16 to work even in WiFi mode. FeelFpv / Feelfpv tinywhoop.


Edit:  It will run offline mode also so no ads is a plus.

22 octobre 2026 à 21:56

A commenté le post de
Few days ago wind was 40mph sustained with 60mph gust. No rain just sand and dust.
Felt like living in Wyoming were the state flag is 5 feet of chain waving in the wind.


Downloaded a sim just for a fix.

22 octobre 2026 à 18:33

A commenté le post de
@Grande  This shows up in the store search-
Maybe a database error for the Admins to fix in the Drone Builder.

GEPRC Taker F405 BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 50A 4in1 ESC)


17 octobre 2026 à 15:09

A commenté le post de
@oldguyFPV 

Most of the Urban pilots don't get to experience the hidden danger in that photo known as "Barbwire". 

17 octobre 2026 à 11:02

A commenté le post de
One word "Introspection".


Beautiful shot reminds me of some areas in northern Arizona.

14 octobre 2026 à 13:53

9 octobre 2026 à 17:39

A commenté le post de
@AurilFPV  I fly both epp and styro , 2 ultrafly furious 3ds, a styro Ripmax alienator that is glassed approaching almost 20 years old. I have flown epp combat wings and they get shredded by APC props. FPV in combat is fun but you lose spatial awareness that LOS gives you with 10 people flying combat. A Coroplast delta or combat wing is the A10 Warthog of RC flying for its durability. That's why I recommend coroplast and it's light as any foam and for $40 for a 4x8 sheet you can build DIY 2-4 planes depending on size.

9 octobre 2026 à 02:20

A commenté le post de
@Zeal-FPV epp becomes brittle over time and if you apply any type of chemical fastener it becomes extra brittle at that joint. I've been flying a very very long time. 

8 octobre 2026 à 19:59

A commenté le post de
Not a fan of $100 styro foam that cost pennies to produce. Coroplast Delta just as fast more durable. "SPAD to the bone" might get you some free plans for a build. 

5 octobre 2026 à 22:51

A commenté le post de
I learned component level repair and soldering from a 6th grade teacher(electronics class). Although it was macro then and not micro I can still troubleshoot. What do the kids learn today in the 6th grade.


Open source tech will be counterfeit but it's today's societal norms. I truly hope OpenDrone is successful.

5 octobre 2026 à 15:51

A commenté le post de
If your prone to losing small parts, disassemble in a 1 or 2 gallon clear plastic bag. Make sure your hands are clean and dry so that e clips, c clips, washers don't stick to your skin. Small parts are easy to lose. If you need to lube the bearings don't use oil it will attract dirt and debris. There are silicone sprays that dry after you apply it.

4 octobre 2026 à 22:08

A commenté le post de
@w4s1m  Clay is good to remove debris, automotive detailing clay works well.

4 octobre 2026 à 01:29

A commenté le post de
Using a raspberry pi pico is brilliant on the FC.
The ability to Fork the hardware might fuel more growth in the USA due to regulation.


 I'm retired so lately I've been working with HaLow wifi (Morse Micro), too bad the ip protocols induce latency long range. But the low power consumption makes up for it . Been working on long range ground FPV.



4 octobre 2026 à 00:02

A publié un post

OpenDrone


Anyone else excited by the new 3 words.


Open Source Hardware


A couple of new videos make sure you watch before ordering. I have no dog in this fight, but I fully support the Open Source Hardware movement.

Prenons notre envol ensemble et propulsons le monde des drones FPV vers de nouveaux sommets.

© 2026 DIYFPV. Tous droits réservés.