S

SiO2

Zuletzt gesehen: 23. Okt., 13:33
Follower
2
Folge ich
0
Positive Bewertungen
0
Beiträge
1
Noch keine Biografie...

Aktivitätsfeed

23. Oktober 2026 um 12:47

Hat den Beitrag von kommentiert
Nothing for Windows but I just tried- FeelFPV tinywhoop on Android ran quite well the controller setup was clunky but ran well once configured. I did try it on Google play for Windows but can't configure my tx16 to work even in WiFi mode. FeelFpv / Feelfpv tinywhoop.


Edit:  It will run offline mode also so no ads is a plus.

22. Oktober 2026 um 21:56

Hat den Beitrag von kommentiert
Few days ago wind was 40mph sustained with 60mph gust. No rain just sand and dust.
Felt like living in Wyoming were the state flag is 5 feet of chain waving in the wind.


Downloaded a sim just for a fix.

22. Oktober 2026 um 18:33

Hat den Beitrag von kommentiert
@Grande  This shows up in the store search-
Maybe a database error for the Admins to fix in the Drone Builder.

GEPRC Taker F405 BLS 3-6S 30x30 Stack/Combo (F405 FC / 8Bit 50A 4in1 ESC)


17. Oktober 2026 um 15:09

Hat den Beitrag von kommentiert
@oldguyFPV 

Most of the Urban pilots don't get to experience the hidden danger in that photo known as "Barbwire". 

17. Oktober 2026 um 11:02

Hat den Beitrag von kommentiert
One word "Introspection".


Beautiful shot reminds me of some areas in northern Arizona.

14. Oktober 2026 um 13:53

Hat den Build von kommentiert: My first build ........., yet to do

9. Oktober 2026 um 17:39

Hat den Beitrag von kommentiert
@AurilFPV  I fly both epp and styro , 2 ultrafly furious 3ds, a styro Ripmax alienator that is glassed approaching almost 20 years old. I have flown epp combat wings and they get shredded by APC props. FPV in combat is fun but you lose spatial awareness that LOS gives you with 10 people flying combat. A Coroplast delta or combat wing is the A10 Warthog of RC flying for its durability. That's why I recommend coroplast and it's light as any foam and for $40 for a 4x8 sheet you can build DIY 2-4 planes depending on size.

9. Oktober 2026 um 02:20

Hat den Beitrag von kommentiert
@Zeal-FPV epp becomes brittle over time and if you apply any type of chemical fastener it becomes extra brittle at that joint. I've been flying a very very long time. 

8. Oktober 2026 um 19:59

Hat den Beitrag von kommentiert
Not a fan of $100 styro foam that cost pennies to produce. Coroplast Delta just as fast more durable. "SPAD to the bone" might get you some free plans for a build. 

5. Oktober 2026 um 22:51

Hat den Beitrag von kommentiert
I learned component level repair and soldering from a 6th grade teacher(electronics class). Although it was macro then and not micro I can still troubleshoot. What do the kids learn today in the 6th grade.


Open source tech will be counterfeit but it's today's societal norms. I truly hope OpenDrone is successful.

5. Oktober 2026 um 15:51

Hat den Beitrag von kommentiert
If your prone to losing small parts, disassemble in a 1 or 2 gallon clear plastic bag. Make sure your hands are clean and dry so that e clips, c clips, washers don't stick to your skin. Small parts are easy to lose. If you need to lube the bearings don't use oil it will attract dirt and debris. There are silicone sprays that dry after you apply it.

4. Oktober 2026 um 22:08

Hat den Beitrag von kommentiert
@w4s1m  Clay is good to remove debris, automotive detailing clay works well.

4. Oktober 2026 um 01:29

Hat den Beitrag von kommentiert
Using a raspberry pi pico is brilliant on the FC.
The ability to Fork the hardware might fuel more growth in the USA due to regulation.


 I'm retired so lately I've been working with HaLow wifi (Morse Micro), too bad the ip protocols induce latency long range. But the low power consumption makes up for it . Been working on long range ground FPV.



4. Oktober 2026 um 00:02

Hat einen Beitrag erstellt

OpenDrone


Anyone else excited by the new 3 words.


Open Source Hardware


A couple of new videos make sure you watch before ordering. I have no dog in this fight, but I fully support the Open Source Hardware movement.

Lass uns gemeinsam abheben und die Welt der FPV-Drohnen auf ein neues Niveau bringen.

© 2026 DIYFPV. Alle Rechte vorbehalten.