PZ-5 “OLD-RED”

Descripción

I’ve tried many frames and components. What I wanted was something close to the “edge” of light weight and durability. With enough power from the motor and esc to run 4s at high thrust output and not burn things up. I built it with these current components after trial and error to achieve a rebuildable power train that performs at close to the limit of 4s. This is keeping in mind I would be ok with an economic build as long as it didn’t hinder flight performance. After running costly gear and cheap cheap I found the middle ground on cost has been the best. With very very few exceptions. In my humble experience. The all up weight is with the dji action 2 and it’s 623 grams the build cost does not include the action 2. This is by far the best flying quad I’ve flown so far, keeping in mind I built it for me. May it serve someone else as well as it does me every day. Keep rippin

Componentes

PZ-5ChasisNo aparece en la listaComes with prints, if needed. Can be found at B2FPV.com
NewBeeDrone FLOW V2 2306.5 2450KV MotorMotoresEn stockDesde $24.99Disponible en 3 tiendas2450kv because this is a 4s build, these have very good torque
FETtec SFOC 50A 4-In-1 ESCESCEn stockDesde $83.49Disponible en 4 tiendasYou will want a 1000uf 50volt cap for analog video noise
FETtec KISS G4-N V1.7 2-6S 30x30 / 20x20 Flight ControllerControlador de vueloEn stockDesde $89.99Disponible en 2 tiendasKiss ultra is also good, as fettec is hard to find
TBS Unify Pro32 HV 25-1000mW 5.8GHz VTX - MMCXTransmisor de vídeoEn stockDesde $50.38Disponible en 12 tiendasYou want to “unlock” it for max power
Runcam Phoenix 2 Special Edition Micro 1000TVL CMOS 4:3/16:9 NTSC/PAL FPV CameraCámaraEn stockDesde $26.04Disponible en 2 tiendasSet 3dnr to zero for lowest latency
TrueRC Matchstick 5.8 SMA Antenna (RHCP)AntenasEn stockDesde $24.99Disponible en 3 tiendasTbs triumph is also good, this is lighter
Happymodel ELRS EP2 Nano ReceiverReceptorEn stockDesde $17.45Disponible en 2 tiendasI set my remote and reciever to 500hz
Ethix P2 Pickle Prop (2CW + 2CCW) PolycarbonateHélicesEn stockDesde $2.84Disponible en 17 tiendasEthix pb&J also good.
Ovonic 1550 4sBateríaNo aparece en la listaOvonic direct on eBay. The wieght on this pack is excellent for the size.
M3 Aluminum Cone Washer (5pcs) - Choose ColorAccesoriosEn stockDesde $1.00Disponible en 3 tiendasJust for fun/style not needed
VHB “double side tape”OtrosNo aparece en la listaUsed to separate and adhere the vtx,vtx antenna,and reciever to the carbon plates.
Aluminum hardwareOtrosNo aparece en la listaCan be found on several Fpv sites, replace everything except the screws that attach the arms to the body
PZ-5 Skids from frozenweb designOtrosNo aparece en la listaOptional, lighter than standard skid, less protection.
Ethix Battery Straps (4pcs)OtrosEn stockDesde $5.99Disponible en 1 tiendasStrong and very light
M3 x 7mm Anti-Vibration Flight Controller Soft Mount Standoff 4 PackOtrosEn stockDesde $2.48Disponible en 6 tiendas
8CM MMCX 90 Degree To SMA ExtensionOtrosEn stockDesde $3.86Disponible en 4 tiendas
Flywoo M3 Clinch Nuts - 20pcs Titanium Press NutsOtrosEn stockDesde $6.75Disponible en 4 tiendasFor the “golden nut” to be used on the stack screws before the esc very strong. Very light

Comentarios (4)

T
tpetersons4d
Adding to my bucket list 💯 thnx for the great build showcase.
- T
  TeleportFpv4d
  Autor
  No problem, it’s a great freestyle rig. Best to ya man!
I
Imp_Syn_FPV3d
Aaaaaand now I want one. Do you have any idea how mad my wife will be? Your fault.
- T
  TeleportFpv3d
  Autor
  It’s a great rig. *cough* “investment” 😀